蓝藻基生物降解共混膜的力学性能

以聚乙烯醇(PVA)和水华蓝藻为主要原料,通过溶液铺膜法制备了蓝藻/PVA共混膜,采用万能试验机,研究了不同助剂对蓝藻/PVA共混膜力学性能的影响。结果表明,蓝藻的添加显著降低了共混膜的力学性能。当添加比例为PVA的1/2时,膜的拉伸强度和断裂伸长率分别比无藻处理下降了65.89%和79.57%。甘油、尿素显著提升了蓝藻/PVA共混膜的断裂伸长率,当添加比例为蓝藻的1/2时,分别能使共混膜的断裂伸长率提高73.20倍和62.02倍。虽然柠檬酸、硅烷偶联剂能够提升蓝藻/PVA共混膜的拉伸强度,但只能在低剂量时促进断裂伸长率的小幅提高,当柠檬酸添加比例为蓝藻的1/40时,膜的断裂伸长率能提高4.41倍,而当硅烷偶联剂添加比例为蓝藻的1/20时,膜的断裂伸长率能提高1.49倍。尿素与甘油复合增塑,更有利于提升共混膜的断裂伸长率。硅烷偶联剂与甘油复合增塑,更有利于提升共混膜的拉伸强度。     

A practical reliability assessment approach and its application for pile-stabilized slopes using FORM and support vector machine

Bulletin of Engineering Geology and the Environment - Many uncertainties exist in pile-stabilized slopes which make their design substantially complicated. In this paper, a first-order reliability...     

电压对电刷镀三价铬镀层性能的影响

在45钢表面电刷镀得到三价铬镀层,镀液组成和工艺条件为:Cr2(SO4)36H2O 0.4 mol/L,甲酸铵0.5 mol/L,氨基乙酸0.5 mol/L,H3BO30.6 mol/L,NaH2PO2 H2O 0.3 mol/L,pH=1.5,温度50°C,镀笔移动速率15 cm/s。研究了电压对镀铬层显微结构、表面粗糙度、厚度、显微硬度和耐磨性的影响。随电压增大,镀层厚度增大,显微硬度和耐磨性均先提高后降低。电压为14 V时,镀层的表面平整,粗糙度为2.387μm,显微硬度为602 HV,耐磨性最好。     

Strain hardening behaviors and mechanisms of polyurethane under various strain rate loading

The uniaxial tension experiments are performed on thermoplastic polyurethane to investigate its mechanical behaviors and related potential mechanisms, and the loading strain rate is designing to be wide ranging from 0.0001 to 1 s⁻¹. It is found that the polyurethane presents an obvious rate-dependence, and the stress strain curves share distinct strain hardening characteristics under the investigated strain rates. Furthermore, the strain hardening ratios are sharing nearly same trends and appear to be influenced by both strain rate and the induced adiabatic heating. Besides, the ratio is also strain-dependent on previous loading history. Then, a two-dimension unit cell model is built to investigate potential equivalent mechanisms, of which the hard phase as inclusion is equivalent with crystallization zone, crosslinking sites, and so forth. The simulation results facilitate to explain the distinct strain hardening ratios, even for the matrix from the extrapolated curves under super-low strain rate loading. Finally, the analogic mechanisms of equivalent hard inclusions are proposed, which can reasonably explain the strain rate- and strain-dependence characteristics of polyurethane mechanical behaviors.     

215/70R17.5 10PR 118/116L无内胎半钢载重子午线轮胎的设计

介绍215/70R17.5 10PR 118/116L无内胎半钢载重子午线轮胎的设计。结构设计:外直径741 mm,断面宽204 mm,行驶面宽度164 mm,胎冠曲线采用反向弧设计,胎圈着合直径442.8 mm,胎圈着合宽度178 mm,断面水平轴位置(H_1/H_2)1.0,采用4条纵向花纹沟设计,花纹深度12 mm,花纹饱和度71.3%,花纹周节数63。施工设计:胎面胶采用乳聚丁苯橡胶与顺丁橡胶并用的生胶体系,带束层采用2层2+7×0.28HT钢丝帘线,胎体采用2层2220dtex/2聚酯帘线,胎体上加贴2层锦纶帘布过渡增强层,胎圈采用软、硬两种三角胶,采用二次法成型机成型、B型液压硫化机硫化。成品性能试验结果表明:轮胎的充气外缘尺寸、强度性能、耐久性能和高速性能均达到相关标准要求,胎圈耐久性能显著提高。     

高光谱激光雷达谱位合一的角度效应分析

高光谱激光雷达以其谱位合一的技术优势为实现超三维精准遥感观测提供了可行途径,因此成为当前激光雷达与高光谱遥感领域共同大力推进的前沿发展方向。目前已有多型原型系统研发出来并得到了原理性验证,然而针对其数据处理核心环节问题的基础技术仍较为欠缺。典型问题之一是不同波段回波信号受激光入射角度的影响,该角度效应限制了高光谱激光雷达实现高性能遥感。以芬兰空间信息研究所高光谱激光雷达原型系统扫描桦树树干为例探讨了该角度效应,发现了不同激光波段对不同入射角度的回波强度响应模式,推导出了角度效应的基本规律及其精细尺度的统计规律,为后续该方向的系统研发、数据处理及信息提取等提供了可借鉴的底层机理与技术基础。     

Ni-Foam Structured Ni-Phyllosilicate Ensemble as an Efficient Monolithic Catalyst for CO2 Methanation

This work proposed a new path to synthesize Ni-phyllosilicate through the reaction of nickel hydroxide and silica sol on the surface of Ni-foam to form the monolithic Ni-phyllosilicate/Ni-foam catalyst. Ni-phyllosilicate could reprint the morphology of nickel hydroxid and firmly anchor on the framework of Ni-foam, which obtained fine Ni particles of 2.8 nm after reduction in H₂ at 650 °C, resulting in high catalytic activity for CO₂ methanation. In addition, the Ni-phyllosilicate/Ni-foam catalyst showed high long-term stability in a 100 h-lifetime test owing to the combined effects of surface confinement of Ni-phyllosilicate, firm anchoring between Ni-phyllosilicate and Ni-foam, as well as the high heat transfer property of Ni-foam.

Graphical Abstract